Find suppliers for this alloyC90500
Chemical Composition
Element
Cu(1,2)PbSnZnFeP(3)Ni(4)AlSSbSi
(1) Cu + Sum of Named Elements 99.7% min. (2) In determining Cu min., Cu may be calculated as Cu + Ni. (3) For continuous castings P shall be 1.5% max. (4) Ni value includes Co.
Min (%)86.09.01.0
Max (%)89.00.3011.03.00.200.051.00.0050.050.200.005
Mechanical Properties*
Form
Temper
Temper Code
Tensile Strength
(ksi)
YS-0.5% Ext
(ksi)
Elongation
(%)
Brinell Hardness, 500 kg load
Izod
(ft-lbs)
Compressive Strength .01 in. set/in.
(ksi)
Fatigue Strength**
(ksi)
Reduction of Area
(%)
As Centrifugal CastAs Centrifugal CastM0240   Min for Standard
40   Min for Standard
45   Typ
18   Min for Standard
18   Min for Standard
22   Typ
20   Min for Standard
20   Min for Standard
25   Typ
75   Typ
10   Typ
40   Typ
13   Typ
As Continuous CastAs Continuous CastM0744   Min for Standard
44   Min for Standard
25   Min for Standard
25   Min for Standard
10   Min for Standard
10   Min for Standard
As Sand CastAs Sand CastM0140   Min for Standard
40   Min for Standard
45   Typ
18   Min for Standard
18   Min for Standard
22   Typ
20   Min for Standard
20   Min for Standard
25   Typ
75   Typ
10   Typ
40   Typ
13   Typ
13   Typ
40   Typ
* Measured at room temperature, 68°F (20°C). ** Fatigue Strength: 100 x 106 cycles, unless indicated as [N] x 106.
Physical Properties
Melting Point - Liquidus°F1830
Melting Point - Solidus°F1570
Densitylb/cu in. at 68°F0.315
Specific Gravity8.72
Electrical Conductivity% IACS at 68°F11
Thermal ConductivityBtu/ sq ft/ ft hr/ °F at 68°F43.2
Coefficient of Thermal Expansion 68-57210⁻⁶ per °F (68 – 572°F)11
Specific Heat CapacityBtu/ lb /°F at 68°F0.09
Modulus of Elasticity in Tensionksi15000
Magnetic Permeability1
Casting Characteristics
Casting Attribute Level
Casting YieldMedium
DrossingLow
Effect of Section SizeHigh
FluidityMedium
GassingMedium
Patternmakers Shrinkageinches per inch3/16
Shrinkage in SolidificationMedium
Fabrication Properties
Technique Suitability Footnote
SolderingExcellent
BrazingGoodSince brazing is performed in the hot short range, strain must be avoided during brazing and cooling.
Oxyacetylene WeldingFair
Gas Shielded Arc WeldingFair
Coated Metal Arc WeldingFair
Machinability Rating30
Common Fabrication Processes
  • Casting
    
Thermal Properties
Treatment Value* Time**
* Temperature is measured in Fahrenheit. ** Time is measured in minutes.
Stress Relief500
Solution Treatment0
Typical uses
Product Category Product Reason Category Reason
Builders HardwareClampsCorrosion ResistanceCorrosion Resistance
ClampsCorrosion ResistanceCorrosion Resistance to Numerous Environments
ClampsMechanical PropertiesModerate Strength
BuildingHeavy Construction EquipmentCorrosion ResistanceCorrosion Resistance
Heavy Construction EquipmentFriction & Wear PropertiesWear Resistance
Heavy Construction EquipmentMechanical PropertiesModerate Strength
Heavy Construction EquipmentPressure TightPressure Tight up to 260 C
ElectricalConnectorsConductivity (Electrical)Electrical Conductivity
ConnectorsConductivity (Thermal)Thermal Conductivity
ConnectorsCorrosion ResistanceCorrosion Resistance
ConnectorsCorrosion ResistanceCorrosion Resistance to Numerous Environments
ConnectorsMechanical PropertiesModerate Strength
FastenersNutsCorrosion ResistanceCorrosion Resistance
NutsMechanical PropertiesModerate Strength
IndustrialBearingsCorrosion ResistanceCorrosion Resistance
BearingsFriction & Wear PropertiesLow Co-efficient of Friction
BearingsFriction & Wear PropertiesWear Resistance
BearingsMechanical PropertiesModerate Strength
BushingsCorrosion ResistanceCorrosion Resistance
BushingsFriction & Wear PropertiesLow Co-efficient of Friction
BushingsFriction & Wear PropertiesWear Resistance
BushingsMechanical PropertiesModerate Strength
Expansion BearingsCorrosion ResistanceCorrosion Resistance
Expansion BearingsFriction & Wear PropertiesWear Resistance
Expansion BearingsMechanical PropertiesModerate Strength
Finishing Dies for Wood Pulp IndustryCorrosion ResistanceCorrosion Resistance
Finishing Dies for Wood Pulp IndustryCorrosion ResistanceCorrosion Resistance to Fresh Water
Finishing Dies for Wood Pulp IndustryCorrosion ResistanceCorrosion Resistance to Numerous Environments
Finishing Dies for Wood Pulp IndustryCorrosion ResistanceCorrosion Resistance to Saline Solutions
Finishing Dies for Wood Pulp IndustryFriction & Wear PropertiesWear Resistance
Finishing Dies for Wood Pulp IndustryMechanical PropertiesModerate Strength
Finishing Dies for Wood Pulp IndustryPressure TightPressure Tight up to 260 C
Gear BlanksCorrosion ResistanceCorrosion Resistance
Gear BlanksFriction & Wear PropertiesWear Resistance
Gear BlanksMachining PropertiesMachinability, Good
Gear BlanksMechanical PropertiesModerate Strength
GearsCorrosion ResistanceCorrosion Resistance
GearsFriction & Wear PropertiesLow Co-efficient of Friction
GearsFriction & Wear PropertiesWear Resistance
GearsMachining PropertiesMachinability, Good
GearsMechanical PropertiesModerate Strength
Piston RingsCorrosion ResistanceCorrosion Resistance
Piston RingsFriction & Wear PropertiesWear Resistance
Piston RingsMechanical PropertiesModerate Strength
Piston RingsPressure TightPressure Tight up to 260 C
Pump BodiesCorrosion ResistanceCorrosion Resistance
Pump BodiesCorrosion ResistanceCorrosion Resistance to Fresh Water
Pump BodiesCorrosion ResistanceCorrosion Resistance to Numerous Environments
Pump BodiesCorrosion ResistanceCorrosion Resistance to Saline Solutions
Pump BodiesMechanical PropertiesModerate Strength
Pump BodiesPressure TightPressure Tight up to 260 C
Pump ImpellersCorrosion ResistanceCorrosion Resistance
Pump ImpellersCorrosion ResistanceCorrosion Resistance to Fresh Water
Pump ImpellersCorrosion ResistanceCorrosion Resistance to Numerous Environments
Pump ImpellersCorrosion ResistanceCorrosion Resistance to Saline Solutions
Pump ImpellersFriction & Wear PropertiesWear Resistance
Pump ImpellersMechanical PropertiesModerate Strength
Pump ImpellersPressure TightPressure Tight up to 260 C
Seal RingsCorrosion ResistanceCorrosion Resistance
Seal RingsFriction & Wear PropertiesWear Resistance
Seal RingsMechanical PropertiesModerate Strength
Valve BodiesCorrosion ResistanceCorrosion Resistance
Valve BodiesFriction & Wear PropertiesWear Resistance
Valve BodiesMechanical PropertiesModerate Strength
Valve BodiesPressure TightPressure Tight up to 260 C
ValvesCorrosion ResistanceCorrosion Resistance
ValvesFriction & Wear PropertiesWear Resistance
ValvesMechanical PropertiesModerate Strength
Worm GearsCorrosion ResistanceCorrosion Resistance
Worm GearsFriction & Wear PropertiesWear Resistance
Worm GearsMechanical PropertiesModerate Strength
PlumbingSteam FittingsCorrosion ResistanceCorrosion Resistance
Steam FittingsCorrosion ResistanceCorrosion Resistance to Numerous Environments
Steam FittingsMechanical PropertiesModerate Strength
Steam FittingsPressure TightPressure Tight up to 260 C
Water ConditionersCorrosion ResistanceCorrosion Resistance
Water ConditionersCorrosion ResistanceCorrosion Resistance to Fresh Water
Water ConditionersCorrosion ResistanceCorrosion Resistance to Saline Solutions
Water ConditionersMechanical PropertiesModerate Strength
Applicable Specifications
Form Sub-Form System Standard Description
As Centrifugal CastCastingsAMS4845TIN BRONZE CASTINGS, SAND AND CENTRIFUGAL, AS CAST
CastingsASTMB271/B271MCOPPER BASE ALLOY CENTRIFUGAL CASTINGS
CastingsSAEJ461WROUGHT AND CAST COPPER ALLOYS
CastingsSAEJ462CAST COPPER ALLOYS
As Continuous CastCastingsASTMB505/B505MCOPPER BASE ALLOY CONTINUOUS CASTINGS
CastingsSAEJ461WROUGHT AND CAST COPPER ALLOYS
CastingsSAEJ462CAST COPPER ALLOYS
As Sand CastCastingsAMS4845TIN BRONZE CASTINGS, SAND AND CENTRIFUGAL, AS CAST
CastingsASTMB22/B22MBRONZE CASTINGS FOR BRIDGES AND TURNTABLES
CastingsASTMB584COPPER ALLOY SAND CASTINGS FOR GENERAL APPLICATIONS
CastingsASTMB763/B763MCOPPER ALLOY SAND CASTINGS FOR VALVE APPLICATIONS
CastingsSAEJ461WROUGHT AND CAST COPPER ALLOYS
CastingsSAEJ462CAST COPPER ALLOYS
Ingot
ASTMB30COPPER BASE ALLOYS IN INGOT FORM
Corrosion Properties

No information available.