Find suppliers for this alloy
C92300
| Elements | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Cu(1,2) | Pb | Sn | Zn | Fe | P(3) | Ni(4) | Al | S | Sb | Si | |
|
(1) Cu + Sum of Named Elements 99.3% min. (2) In determining Cu min., Cu may be calculated as Cu + Ni. (3) For continuous castings P shall be 1.5% max. (4) Ni value includes Co. |
|||||||||||
| Min (%) | 85.0 | 0.30 | 7.5 | 2.5 | |||||||
| Max (%) | 89.0 | 1.0 | 9.0 | 5.0 | 0.25 | 0.05 | 1.0 | 0.005 | 0.05 | 0.25 | 0.005 |
| Form | Temper | Temper Code | Tensile Strength (ksi) |
YS-0.5% Ext (ksi) |
Elongation (%) |
Brinell Hardness, 500 kg load | Izod (ft-lbs) |
Compressive Strength .001 in. set/in. (ksi) |
Compressive Strength .1 in. set/in. (ksi) |
|---|---|---|---|---|---|---|---|---|---|
| * Measured at room temperature, 68°F (20°C). | |||||||||
| As Centrifugal Cast | As Centrifugal Cast | M02 |
36 Min for Standard 36 Min for Standard |
16 Min for Standard |
18 Min for Standard 18 Min for Standard |
||||
| As Continuous Cast | As Continuous Cast | M07 |
40 Min for Standard 40 Min for Standard |
19 Min for Standard |
16 Min for Standard 16 Min for Standard |
||||
| As Sand Cast | As Sand Cast | M01 |
36 Min for Standard 36 Min for Standard 40 Typ |
16 Min for Standard 20 Typ |
18 Min for Standard 18 Min for Standard 25 Typ |
70 Typ |
12 Typ | 10 Typ | 35 Typ |
| Melting Point - Liquidus°F | 1830 |
|---|---|
| Melting Point - Solidus°F | 1570 |
| Densitylb/cu in. at 68°F | 0.317 |
| Specific Gravity | 8.77 |
| Electrical Conductivity% IACS at 68°F | 12 |
| Thermal ConductivityBtu/ sq ft/ ft hr/ °F at 68°F | 43.2 |
| Coefficient of Thermal Expansion 68-39210 to -6 power per °F (68 – 392°F) | 10 |
| Specific Heat CapacityBtu/ lb /°F at 68°F | 0.09 |
| Modulus of Elasticity in Tensionksi | 14000 |
| Incipient Melting°F | 600 |
| Casting Attribute | Level |
|---|---|
| Casting Yield | Medium |
| Drossing | Low |
| Effect of Section Size | High |
| Fluidity | Medium |
| Gassing | Medium |
| Patternmakers Shrinkage inches per inch | 3/16 |
| Shrinkage in Solidification | Low |
| Technique | Suitability |
|---|---|
| Soldering | Excellent |
| Brazing | Good |
| Oxyacetylene Welding | Not Recommended |
| Gas Shielded Arc Welding | Not Recommended |
| Coated Metal Arc Welding | Not Recommended |
| Machinability Rating | 42 |
Common Fabrication Processes
No fabrication process properties for this alloy
| Treatment | Value* | Time** | ||
|---|---|---|---|---|
| * Temperature is measured in Fahrenheit. ** Time is measured in minutes. | ||||
| Stress Relief | 500 | |||
| Solution Treatment | 0 | |||
| Product Category | Product | Reason Category | Reason |
|---|---|---|---|
| Builders Hardware | Structural Castings | Corrosion Resistance | Corrosion Resistance |
| Structural Castings | Corrosion Resistance | Corrosion Resistance to Numerous Environments | |
| Structural Castings | Machining Properties | Machinability, Good | |
| Structural Castings | Mechanical Properties | Moderate Strength | |
| Fasteners | Nuts | Corrosion Resistance | Corrosion Resistance |
| Nuts | Corrosion Resistance | Corrosion Resistance to Fresh Water | |
| Nuts | Corrosion Resistance | Corrosion Resistance to Numerous Environments | |
| Nuts | Corrosion Resistance | Corrosion Resistance to Saline Solutions | |
| Nuts | Machining Properties | Machinability, Good | |
| Nuts | Mechanical Properties | Moderate Strength | |
| Industrial | Bearings | Corrosion Resistance | Corrosion Resistance |
| Bearings | Corrosion Resistance | Corrosion Resistance to Numerous Environments | |
| Bearings | Friction & Wear Properties | Wear Resistance | |
| Bearings | Machining Properties | Machinability, Good | |
| Bearings | Mechanical Properties | Moderate Strength | |
| Bushings | Corrosion Resistance | Corrosion Resistance | |
| Bushings | Friction & Wear Properties | Wear Resistance | |
| Bushings | Machining Properties | Machinability, Good | |
| Bushings | Mechanical Properties | Moderate Strength | |
| Gears | Corrosion Resistance | Corrosion Resistance | |
| Gears | Friction & Wear Properties | Wear Resistance | |
| Gears | Machining Properties | Machinability, Good | |
| Gears | Mechanical Properties | Moderate Strength | |
| High Pressure Hydraulic Equipment | Corrosion Resistance | Corrosion Resistance | |
| High Pressure Hydraulic Equipment | Corrosion Resistance | Corrosion Resistance to Fresh Water | |
| High Pressure Hydraulic Equipment | Corrosion Resistance | Corrosion Resistance to Numerous Environments | |
| High Pressure Hydraulic Equipment | Corrosion Resistance | Corrosion Resistance to Saline Solutions | |
| High Pressure Hydraulic Equipment | Friction & Wear Properties | Wear Resistance | |
| High Pressure Hydraulic Equipment | Machining Properties | Machinability, Good | |
| High Pressure Hydraulic Equipment | Mechanical Properties | Moderate Strength | |
| High Pressure Hydraulic Equipment | Pressure Tight | Pressure Tight below 260 C | |
| Piston Rings | Corrosion Resistance | Corrosion Resistance | |
| Piston Rings | Corrosion Resistance | Corrosion Resistance to Numerous Environments | |
| Piston Rings | Machining Properties | Machinability, Good | |
| Piston Rings | Mechanical Properties | Moderate Strength | |
| Piston Rings | Pressure Tight | Pressure Tight below 260 C | |
| Pump Impellers | Corrosion Resistance | Corrosion Resistance | |
| Pump Impellers | Corrosion Resistance | Corrosion Resistance to Fresh Water | |
| Pump Impellers | Corrosion Resistance | Corrosion Resistance to Saline Solutions | |
| Pump Impellers | Friction & Wear Properties | Wear Resistance | |
| Pump Impellers | Machining Properties | Machinability, Good | |
| Pump Impellers | Mechanical Properties | Moderate Strength | |
| Pump Parts | Corrosion Resistance | Corrosion Resistance | |
| Pump Parts | Corrosion Resistance | Corrosion Resistance to Fresh Water | |
| Pump Parts | Corrosion Resistance | Corrosion Resistance to Numerous Environments | |
| Pump Parts | Corrosion Resistance | Corrosion Resistance to Saline Solutions | |
| Pump Parts | Friction & Wear Properties | Wear Resistance | |
| Pump Parts | Machining Properties | Machinability, Good | |
| Pump Parts | Mechanical Properties | Moderate Strength | |
| Valve Bodies | Corrosion Resistance | Corrosion Resistance | |
| Valve Bodies | Corrosion Resistance | Corrosion Resistance to Fresh Water | |
| Valve Bodies | Corrosion Resistance | Corrosion Resistance to Saline Solutions | |
| Valve Bodies | Machining Properties | Machinability, Good | |
| Valve Bodies | Mechanical Properties | Moderate Strength | |
| Plumbing | High Pressure Steam Equipment | Corrosion Resistance | Corrosion Resistance |
| High Pressure Steam Equipment | Corrosion Resistance | Corrosion Resistance to Fresh Water | |
| High Pressure Steam Equipment | Corrosion Resistance | Corrosion Resistance to Numerous Environments | |
| High Pressure Steam Equipment | Corrosion Resistance | Corrosion Resistance to Saline Solutions | |
| High Pressure Steam Equipment | Machining Properties | Machinability, Good | |
| High Pressure Steam Equipment | Mechanical Properties | Moderate Strength | |
| High Pressure Steam Equipment | Pressure Tight | Pressure Tight below 260 C |
| Form | Specific Sub-Form | Application | System | Standard | Description |
|---|---|---|---|---|---|
| As Centrifugal Cast | Castings | SAE | J462 | CAST COPPER ALLOYS | |
| Castings | ASTM | B271/B271M | COPPER BASE ALLOY CENTRIFUGAL CASTINGS | ||
| Castings | SAE | J461 | WROUGHT AND CAST COPPER ALLOYS | ||
| As Continuous Cast | Castings | SAE | J462 | CAST COPPER ALLOYS | |
| Castings | ASTM | B505/B505M | COPPER BASE ALLOY CONTINUOUS CASTINGS | ||
| Castings | SAE | J461 | WROUGHT AND CAST COPPER ALLOYS | ||
| As Sand Cast | Castings | SAE | J461 | WROUGHT AND CAST COPPER ALLOYS | |
| Castings | ASTM | B584 | COPPER ALLOY SAND CASTINGS FOR GENERAL APPLICATIONS | ||
| Castings | ASTM | B763/B763M | COPPER ALLOY SAND CASTINGS FOR VALVE APPLICATIONS | ||
| Ingot | |||||
| ASTM | B30 | COPPER BASE ALLOYS IN INGOT FORM |
Corrosion Properties
No Corrosion Properties Available.