Find suppliers for this alloy C93200
Chemical Composition
Elements
Cu(1,2) Pb Sn Zn Fe P(3) Ni(4) Al S Sb Si
(1) Cu + Sum of Named Elements 99.0% min.
(2) In determining Cu min., Cu may be calculated as Cu + Ni.
(3) For continuous castings P shall be 1.5% max.
(4) Ni value includes Co.
Min (%) 81.0 6.0 6.3 1.0
Max (%) 85.0 8.0 7.5 4.0 0.20 0.15 1.0 0.005 0.08 0.35 0.005
Mechanical Properties *
Form Temper Temper Code Tensile Strength
(ksi)
YS-0.5% Ext
(ksi)
Elongation
(%)
Brinell Hardness, 500 kg load Izod
(ft-lbs)
Compressive Strength .1 in. set/in.
(ksi)
Fatigue Strength**
(ksi)
Proportional Limit
(ksi)
* Measured at room temperature, 68°F (20°C). ** Fatigue Strength: 100 x 106 cycles, unless indicated as [N] x 106.
As Centrifugal Cast As Centrifugal Cast M02 30 Min for Standard
14 Min for Standard
15 Min for Standard
As Continuous Cast As Continuous Cast M07 35 Min for Standard
35 Min for Standard
20 Min for Standard
10 Min for Standard
10 Min for Standard
As Sand Cast As Sand Cast M01 30 Min for Standard
30 Min for Standard
35 Typ
14 Min for Standard
18 Typ
15 Min for Standard
15 Min for Standard
20 Typ
65 Typ
6 Typ 46 Typ 16 Typ 8.5 Typ
Physical Properties
Melting Point - Liquidus°F 1790
Melting Point - Solidus°F 1570
Densitylb/cu in. at 68°F 0.322
Specific Gravity 8.91
Electrical Conductivity% IACS at 68°F 12
Thermal ConductivityBtu/ sq ft/ ft hr/ °F at 68°F 33.6
Coefficient of Thermal Expansion 68-21210 to -6 power per °F (68 – 212°F) 10
Specific Heat CapacityBtu/ lb /°F at 68°F 0.09
Modulus of Elasticity in Tensionksi 14500
Casting Characteristics
Casting Attribute Level
Casting Yield High
Drossing Low
Effect of Section Size Medium
Fluidity Medium
Gassing Medium
Patternmakers Shrinkage inches per inch 7/32
Shrinkage in Solidification Low
Fabrication Properties
Technique Suitability
Soldering Excellent
Brazing Good
Oxyacetylene Welding Not Recommended
Gas Shielded Arc Welding Not Recommended
Coated Metal Arc Welding Not Recommended
Machinability Rating 70
Common Fabrication Processes

No fabrication process properties for this alloy

Thermal Properties
Treatment Value* Time**
* Temperature is measured in Fahrenheit. ** Time is measured in minutes.
Stress Relief 500
Solution Treatment 0
Typical uses
Product Category Product Reason Category Reason
Automotive Automotive Fittings Corrosion Resistance Corrosion Resistance
Automotive Fittings Corrosion Resistance Corrosion Resistance to Numerous Environments
Automotive Fittings Machining Properties Machinability, Good
Automotive Fittings Mechanical Properties Relatively Low Strength
Fasteners Washers Corrosion Resistance Corrosion Resistance
Washers Corrosion Resistance Corrosion Resistance to Numerous Environments
Washers Machining Properties Machinability, Good
Washers Mechanical Properties Relatively Low Strength
Industrial Bearings Corrosion Resistance Corrosion Resistance
Bearings Corrosion Resistance Corrosion Resistance to Numerous Environments
Bearings Friction & Wear Properties Anti-Seizing Properties
Bearings Friction & Wear Properties Low Coefficient of Friction
Bearings Friction & Wear Properties Wear Resistance
Bearings Machining Properties Machinability, Good
Bearings Mechanical Properties Relatively Low Strength
Bearings for Cranes Corrosion Resistance Corrosion Resistance
Bearings for Cranes Corrosion Resistance Corrosion Resistance to Numerous Environments
Bearings for Cranes Friction & Wear Properties Anti-Seizing Properties
Bearings for Cranes Friction & Wear Properties Low Coefficient of Friction
Bearings for Cranes Friction & Wear Properties Wear Resistance
Bearings for Cranes Machining Properties Machinability, Good
Bearings for Cranes Mechanical Properties Relatively Low Strength
Bushings Corrosion Resistance Corrosion Resistance
Bushings Corrosion Resistance Corrosion Resistance to Numerous Environments
Bushings Friction & Wear Properties Low Coefficient of Friction
Bushings Friction & Wear Properties Wear Resistance
Bushings Machining Properties Machinability, Good
Bushings Mechanical Properties Relatively Low Strength
Diesel Engine Wrist Pin Bushings Corrosion Resistance Corrosion Resistance
Diesel Engine Wrist Pin Bushings Corrosion Resistance Corrosion Resistance to Many Industrial Chemicals
Diesel Engine Wrist Pin Bushings Friction & Wear Properties Anti-Seizing Properties
Diesel Engine Wrist Pin Bushings Friction & Wear Properties Low Coefficient of Friction
Diesel Engine Wrist Pin Bushings Friction & Wear Properties Wear Resistance
Diesel Engine Wrist Pin Bushings Machining Properties Machinability, Good
Diesel Engine Wrist Pin Bushings Mechanical Properties Relatively Low Strength
Fittings Corrosion Resistance Corrosion Resistance
Fittings Corrosion Resistance Corrosion Resistance to Numerous Environments
Fittings Machining Properties Machinability, Good
Fittings Mechanical Properties Relatively Low Strength
Forging Press Toggle Lever Bearings Corrosion Resistance Corrosion Resistance
Forging Press Toggle Lever Bearings Corrosion Resistance Corrosion Resistance to Numerous Environments
Forging Press Toggle Lever Bearings Friction & Wear Properties Anti-Seizing Properties
Forging Press Toggle Lever Bearings Friction & Wear Properties Low Coefficient of Friction
Forging Press Toggle Lever Bearings Friction & Wear Properties Wear Resistance
Forging Press Toggle Lever Bearings Machining Properties Machinability, Good
Forging Press Toggle Lever Bearings Mechanical Properties Relatively Low Strength
Fuel Pump Bushings Corrosion Resistance Corrosion Resistance
Fuel Pump Bushings Corrosion Resistance Corrosion Resistance to Numerous Environments
Fuel Pump Bushings Friction & Wear Properties Anti-Seizing Properties
Fuel Pump Bushings Friction & Wear Properties Low Coefficient of Friction
Fuel Pump Bushings Friction & Wear Properties Wear Resistance
Fuel Pump Bushings Machining Properties Machinability, Good
Fuel Pump Bushings Mechanical Properties Relatively Low Strength
General Purpose Bushings Corrosion Resistance Corrosion Resistance
General Purpose Bushings Corrosion Resistance Corrosion Resistance to Numerous Environments
General Purpose Bushings Friction & Wear Properties Anti-Seizing Properties
General Purpose Bushings Friction & Wear Properties Low Coefficient of Friction
General Purpose Bushings Friction & Wear Properties Wear Resistance
General Purpose Bushings Machining Properties Machinability, Good
General Purpose Bushings Mechanical Properties Relatively Low Strength
Hydraulic Press Main Lining Corrosion Resistance Corrosion Resistance
Hydraulic Press Main Lining Corrosion Resistance Corrosion Resistance to Many Industrial Chemicals
Hydraulic Press Main Lining Friction & Wear Properties Anti-Seizing Properties
Hydraulic Press Main Lining Friction & Wear Properties Wear Resistance
Hydraulic Press Main Lining Machining Properties Machinability, Good
Hydraulic Press Main Lining Mechanical Properties Relatively Low Strength
Hydraulic Press Stuffing Box Corrosion Resistance Corrosion Resistance
Hydraulic Press Stuffing Box Corrosion Resistance Corrosion Resistance to Numerous Environments
Hydraulic Press Stuffing Box Machining Properties Machinability, Good
Hydraulic Press Stuffing Box Mechanical Properties Relatively Low Strength
Hydraulic Press Stuffing Box Pressure Tight Pressure Tight
Insert Bearings Corrosion Resistance Corrosion Resistance
Insert Bearings Corrosion Resistance Corrosion Resistance to Numerous Environments
Insert Bearings Friction & Wear Properties Low Coefficient of Friction
Insert Bearings Friction & Wear Properties Wear Resistance
Insert Bearings Machining Properties Machinability, Good
Insert Bearings Mechanical Properties Relatively Low Strength
Linkage Bushings for Presses Corrosion Resistance Corrosion Resistance
Linkage Bushings for Presses Corrosion Resistance Corrosion Resistance to Numerous Environments
Linkage Bushings for Presses Friction & Wear Properties Anti-Seizing Properties
Linkage Bushings for Presses Friction & Wear Properties Low Coefficient of Friction
Linkage Bushings for Presses Friction & Wear Properties Wear Resistance
Linkage Bushings for Presses Machining Properties Machinability, Good
Linkage Bushings for Presses Mechanical Properties Relatively Low Strength
Machine Parts Conductivity (Thermal) Thermal Conductivity
Machine Parts Corrosion Resistance Corrosion Resistance
Machine Parts Corrosion Resistance Corrosion Resistance to Numerous Environments
Machine Parts Friction & Wear Properties Anti-Seizing Properties
Machine Parts Friction & Wear Properties Wear Resistance
Machine Parts Machining Properties Machinability, Good
Machine Parts Mechanical Properties Relatively Low Strength
Machine Tool Bearings Corrosion Resistance Corrosion Resistance
Machine Tool Bearings Corrosion Resistance Corrosion Resistance to Numerous Environments
Machine Tool Bearings Friction & Wear Properties Anti-Seizing Properties
Machine Tool Bearings Friction & Wear Properties Low Coefficient of Friction
Machine Tool Bearings Friction & Wear Properties Wear Resistance
Machine Tool Bearings Machining Properties Machinability, Good
Machine Tool Bearings Mechanical Properties Relatively Low Strength
Main Spindle Bearings Corrosion Resistance Corrosion Resistance
Main Spindle Bearings Corrosion Resistance Corrosion Resistance to Numerous Environments
Main Spindle Bearings Friction & Wear Properties Anti-Seizing Properties
Main Spindle Bearings Friction & Wear Properties Low Coefficient of Friction
Main Spindle Bearings Friction & Wear Properties Wear Resistance
Main Spindle Bearings Machining Properties Machinability, Good
Main Spindle Bearings Mechanical Properties Relatively Low Strength
Pump Fixtures Corrosion Resistance Corrosion Resistance
Pump Fixtures Corrosion Resistance Corrosion Resistance to Numerous Environments
Pump Fixtures Machining Properties Machinability, Good
Pump Fixtures Mechanical Properties Relatively Low Strength
Pump Impellers Corrosion Resistance Corrosion Resistance
Pump Impellers Corrosion Resistance Corrosion Resistance to Brackish Water
Pump Impellers Corrosion Resistance Corrosion Resistance to Many Industrial Chemicals
Pump Impellers Corrosion Resistance Corrosion Resistance to Numerous Environments
Pump Impellers Corrosion Resistance Corrosion Resistance to Petroleum Products
Pump Impellers Friction & Wear Properties Wear Resistance
Pump Impellers Machining Properties Machinability, Good
Pump Impellers Mechanical Properties Relatively Low Strength
Pumps Corrosion Resistance Corrosion Resistance
Pumps Corrosion Resistance Corrosion Resistance to Brackish Water
Pumps Corrosion Resistance Corrosion Resistance to Many Industrial Chemicals
Pumps Corrosion Resistance Corrosion Resistance to Numerous Environments
Pumps Friction & Wear Properties Wear Resistance
Pumps Machining Properties Machinability, Good
Pumps Mechanical Properties Relatively Low Strength
Pumps Pressure Tight Pressure Tight
Roll Neck Bearings Corrosion Resistance Corrosion Resistance
Roll Neck Bearings Corrosion Resistance Corrosion Resistance to Numerous Environments
Roll Neck Bearings Friction & Wear Properties Low Coefficient of Friction
Roll Neck Bearings Friction & Wear Properties Wear Resistance
Roll Neck Bearings Machining Properties Machinability, Good
Roll Neck Bearings Mechanical Properties Relatively Low Strength
Rolling Mill Bearings Corrosion Resistance Corrosion Resistance
Rolling Mill Bearings Corrosion Resistance Corrosion Resistance to Numerous Environments
Rolling Mill Bearings Friction & Wear Properties Low Coefficient of Friction
Rolling Mill Bearings Friction & Wear Properties Wear Resistance
Rolling Mill Bearings Machining Properties Machinability, Good
Rolling Mill Bearings Mechanical Properties Relatively Low Strength
Thrust Washers Corrosion Resistance Corrosion Resistance
Thrust Washers Corrosion Resistance Corrosion Resistance to Numerous Environments
Thrust Washers Friction & Wear Properties Wear Resistance
Thrust Washers Machining Properties Machinability, Good
Thrust Washers Mechanical Properties Relatively Low Strength
Trunion Bearings Corrosion Resistance Corrosion Resistance
Trunion Bearings Corrosion Resistance Corrosion Resistance to Numerous Environments
Trunion Bearings Friction & Wear Properties Low Coefficient of Friction
Trunion Bearings Friction & Wear Properties Wear Resistance
Trunion Bearings Machining Properties Machinability, Good
Trunion Bearings Mechanical Properties Relatively Low Strength
Water Pump Bushings Corrosion Resistance Corrosion Resistance
Water Pump Bushings Corrosion Resistance Corrosion Resistance to Brackish Water
Water Pump Bushings Corrosion Resistance Corrosion Resistance to Many Industrial Chemicals
Water Pump Bushings Friction & Wear Properties Anti-Seizing Properties
Water Pump Bushings Friction & Wear Properties Low Coefficient of Friction
Water Pump Bushings Friction & Wear Properties Wear Resistance
Water Pump Bushings Machining Properties Machinability, Good
Water Pump Bushings Mechanical Properties Relatively Low Strength
Applicable Specifications
Form Specific Sub-Form Application System Standard Description
As Centrifugal Cast Castings SAE J461 WROUGHT AND CAST COPPER ALLOYS
Castings SAE J462 CAST COPPER ALLOYS
Castings ASTM B271/B271M COPPER BASE ALLOY CENTRIFUGAL CASTINGS
As Continuous Cast Castings SAE J462 CAST COPPER ALLOYS
Castings SAE J461 WROUGHT AND CAST COPPER ALLOYS
Castings ASTM B505/B505M COPPER BASE ALLOY CONTINUOUS CASTINGS
As Permanent Mold Cast Castings SAE J462 CAST COPPER ALLOYS
Castings SAE J461 WROUGHT AND CAST COPPER ALLOYS
As Sand Cast Castings ASTM B763/B763M COPPER ALLOY SAND CASTINGS FOR VALVE APPLICATIONS
Castings SAE J462 CAST COPPER ALLOYS
Castings ASTM B584 COPPER ALLOY SAND CASTINGS FOR GENERAL APPLICATIONS
ASTM B66 BRONZE CASTINGS IN THE ROUGH FOR LOCOMOTIVE WEARING PARTS
Castings SAE J461 WROUGHT AND CAST COPPER ALLOYS
Ingot ASTM B30 COPPER BASE ALLOYS IN INGOT FORM
Corrosion Properties

No Corrosion Properties Available.